 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747 MNR02 Resistors Chip resistor networks MNR02 (1005 x 2 size) !Features 1) Extremely small and light Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%. 2) High-density mounting Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced. 3) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 4) Convex electrodes Easy to check the fillet after soldering is finished. 5) ROHM resistors have obtained ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it. !Ratings Item Rated power Conditions Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70C. 100 80 POWER LOAD (%) Specifications 0.063W (1 / 16W) at 70C 60 40 20 0 -55 0 70 100 125 155 AMBIENT TEMPERATURE (C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= PxR P: Rated power (W) R: Nominal resistance () Limiting element voltage 25V Nominal resistance Operating temperature See Table 1. -55C to +125C For the very latest product data and news visit angliac.com Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747 MNR02 Resistors Table 1 Resistance tolerance Resistance range () Resistance temperature coefficient (ppm / C) J (5%) 10R1M (E24) 300 *Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. !Characteristics Items Resistance Variation of resistance with temperature Overload Guaranteed value Resistor type J : 5% See Table.1 (2.0%+0.1) A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. (1.0%+0.05) No remarkable abnormality on the appearance. (1.0%+0.05) (3.0%+0.1) Damp heat, steady state (3.0%+0.1) Endurance at 70C (3.0%+0.1) Endurance (1.0%+0.05) Resistance to solvent (1.0%+0.05) Without mechanical damage such as breaks. Test conditions (JIS C 5201-1) JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : -55 / +25 / +125C JIS C 5201-1 4.13 Rated voltage (current) x2.5, 2s. Limiting Element Voltagex2 : 50V JIS C 5201-1 4.17 Rosin*Ethanol (25%WT) Soldering condition : 2355C Duration of immersion : 2.00.5s. JIS C 5201-1 4.18 Soldering condition : 2605C Duration of immersion : 101s. JIS C 5201-1 4.19 Test temp. : -55C~+125C 5cyc JIS C 5201-1 4.24 40C, 93%RH Test time : 1,000h~1,048h JIS C 5201-1 4.25.1 Rated voltage (current), 70C 1.5h : ON - 0.5h : OFF Test time : 1,000h~1,048h JIS C 5201-1 4.25.3 125C Test time : 1,000h~1,048h JIS C 5201-1 4.29 235C, Immersion cleaning, 50.5min. Solvent : 2-propanol JIS C 5201-1 4.33 Solderability Resistance to soldering heat Rapid change of temperature Bend strength of the end face plating For the very latest product data and news visit angliac.com Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747 MNR02 Resistors !External dimensions (Units: mm) 1.00.1 6 1 0.250.1 B Cross section A-A' 0.20.1 No. 5 Material Thick dielectric glaze of ruthenium Thick film of silver for primary electrode Nickel-coated secondary electrode External electrode coated with Sn/Pb or Sn Alumina substrate Overcoating 1 2 3 4 1.00.1 A A' Cross section B-B' 6 1 5 5 B' +0.1 0.33 -0.05 +0.05 0.34 -0.1 0.350.1 2 3 4 6 0.68 !Equivalent circuit R1 R2 R1 = R2 For the very latest product data and news visit angliac.com Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747 MNR02 Resistors !Packaging Reel Taping P0 P2 0 D E A0 B0 F W 02 04 06 08 08 06 04 A B D 02 P1 Heat crimp cover / Tape Thick paper (Underside paper tape) mount Chip network resistors Square punchout hole T2 C Label EIAJ ET-7200A compliant (Units: mm) W (Units: mm) F 3.50.05 P0 4.00.1 E 1.750.1 P1 2.00.1 A0 1.170.1 P2 2.00.05 B0 1.170.1 T2 Max. 0.5 A 180 0 -3 B 60 +1 0 9 C +1.0 0 D 130.2 8.00.3 D0 +0.1 1.5 0 !Product designation Part No. Packaging / Processing specifications Circuit configuration code A MNR02 Resistance tolerance J 5% Nominal resistance 3-digit IEC coding system Code Part No. Packaging Taping M0 MNR02 Package style Paper tape with reel (10,000) For the very latest product data and news visit angliac.com Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747 MNR02 Resistors !Electrical characteristics TEMPERATURE COEFFICIENT (ppm / C) 6.0 5.0 4.0 DC RESISTANCE (%) 400 300 200 R/R (%) 6.0 JIS C 5201-1 4.8 SAMPLE SIZE : n=20pcs 25C / -55C 25C / 125C JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20C 65%RH 4.0 2.0 0 -2.0 -4.0 -6.0 3.0 2.0 1.0 0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 10 100 1k 10k 100k 1M JIS C 5201-1 4.13 SAMPLE SIZE : n=20pcs RATED VOLTAGEx2.5TIMES 2s LIMITING ELEMENT VOLTAGEx2 : 100V 100 0 -100 -200 -300 -400 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE () RESISTANCE () RESISTANCE () Fig.2 Resistance Fig.3 Variation resistance with temperature Fig.4 Overload 3.0 2.0 1.0 R/R (%) 3.0 6.0 JIS C 5201-1 4.19 SAMPLE SIZE : n=20pcs -55C / 125C 5cyc JIS C 5201-1 4.18 SAMPLE SIZE : n=20pcs SOLDERING CONDITION : 260C 10s 2.0 1.0 0 -1.0 -2.0 -3.0 4.0 2.0 JIS C 5201-1 4.24 SAMPLE SIZE : n=20pcs 40C 93%RH WITH NO LOAD 1,000h R/R (%) R/R (%) 10 100 1k 10k 100k 1M 0 -1.0 -2.0 -3.0 0 -2.0 -4.0 -6.0 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE () RESISTANCE () RESISTANCE () Fig.5 Resistance to soldering heat Fig.6 Rapid change of temperature Fig.7 Damp heat, steady state 6.0 4.0 2.0 R/R (%) 6.0 JIS C 5201-1 4.25.1 SAMPLE SIZE : n=20pcs 70C 1,000h OVERLOAD : THE RATED VOLTAGE 4.0 2.0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=20pcs 125C WITH NO LOAD 1,000h R/R (%) 0 -2.0 -4.0 -6.0 0 -2.0 -4.0 -6.0 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE () RESISTANCE () Fig.8 Endurance at 70C Fig.9 Endurance For the very latest product data and news visit angliac.com |
Price & Availability of MNR02
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |